Ifm – PI2899

Flush pressure sensor with display; Min. insulation resistance [MΩ] : 100; (500 V DC); Protection class : III; Reverse polarity protection : yes; Measuring principle : hydrostatic; Integrated watchdog : yes; Step response time analogue output [ms] : 45; Min. response time of switching output (dAP) [ms] : 3; Step response time analogue output [ms] : 7; Total number of outputs : 2; Output signal : switching signal; analogue signal; IO-Link; (configurable); Electrical design : PNP/NPN; Number of digital outputs : 2; Output function : normally open / normally closed; (parameterisable); Number of analogue outputs : 1; Analogue current output [mA] : 4...20, invertible; (scalable); Short-circuit protection : yes; Type of short-circuit protection : pulsed; Overload protection : yes; Measuring range : -0.124...2.5 bar: -124...2500 mbar: -1.8...36.27 psi: -12.4...250 kPa; Set point SP : -0.12...2.5 bar: -1.74...36.27 psi: -12...250 kPa; Reset point rP : -0.124...2.496 bar: -1.8...36.21 psi: -12.4...249.6 kPa; Analogue start point : -0.124...1.88 bar: -1.8...27.27 psi: -12.4...188 kPa; Analogue end point : 0.5...2.5 bar: 7.26...36.27 psi: 50...250 kPa; In steps of : 0.002 bar: 0.03 psi: 0.2 kPa; Factory setting : SP1 = 0.624 bar: rP1 = 0.574 bar | SP2 = 1.874 bar: rP2 = 1.824 bar | ASP = 0.000 bar: AEP = 2.500 bar; Switch point accuracy [% of the span] : < ± 0,2; (Turn down 1:1); Repeatability [% of the span] : < ± 0,1; (with temperature fluctuations < 10 K; Turn down 1:1); Characteristics deviation [% of the span] : < ± 0,2; (Turn down 1:1 , linearity, incl. hysteresis and repeatability , limit value setting to DIN EN IEC 62828-1); Linearity deviation [% of the span] : < ± 0,15; (Turn down 1:1); Hysteresis deviation [% of the span] : < ± 0,15; (Turn down 1:1); Long-term stability [% of the span] : < ± 0,1; (Turn down 1:1; per year); Temperature coefficient zero point [% of the span / 10 K] : < ± 0,05; (0...70 °C); Temperature coefficient span [% of the span / 10 K] : < ± 0,15; (0...70 °C); Damping for the switching output dAP [s] : 0...30; Damping for the analogue output dAA [s] : 0.01...99.99; Communication interface : IO-Link; Transmission type : COM2 (38,4 kBaud); IO-Link revision : 1.0; Profiles : no profile; SIO mode : yes; Required master port type : A; Process data analogue : 1; Process data binary : 2; Min. process cycle time [ms] : 2.3; Supported DeviceIDs : Type of operation: DeviceID | Default: 159; Ambient temperature [°C] : -25...80; Storage temperature [°C] : -40...100; Materials : stainless steel (1.4404 / 316L); FKM; PTFE; PBT; PEI; PFA; Materials (wetted parts) : ceramics (99.9 % Al2O3); stainless steel (1.4435 / 316L); surface characteristics: Ra < 0,4 / Rz 4; PTFE; Min. pressure cycles : 100 million; Process connection : threaded connection G 1 external thread sealing cone - Attention: The unit must only be installed in a process connection for G1 sealing cone.; The G1A sealing cone of the unit is only suited for adapters with metal end stop.; Display unit : bar; kPa; psi; inH2O; mWS; % of the span

Flush pressure sensor with display; Min. insulation resistance [MΩ] : 100; (500 V DC); Protection class : III; Reverse polarity protection : yes; Measuring principle : hydrostatic; Integrated watchdog : yes; Step response time analogue output [ms] : 45; Min. response time of switching output (dAP) [ms] : 3; Step response time analogue output [ms] : 7; Total number of outputs : 2; Output signal : switching signal; analogue signal; IO-Link; (configurable); Electrical design : PNP/NPN; Number of digital outputs : 2; Output function : normally open / normally closed; (parameterisable); Number of analogue outputs : 1; Analogue current output [mA] : 4...20, invertible; (scalable); Short-circuit protection : yes; Type of short-circuit protection : pulsed; Overload protection : yes; Measuring range : -0.0124...0.25 bar: -12.4...250 mbar: -5...100.4 inH2O: -1.24...25 kPa; Set point SP : -12...250 mbar: -4.8...100.4 inH2O: -1.2...25 kPa; Reset point rP : -12.4...249.6 mbar: -5...100.2 inH2O: -1.24...24.96 kPa; Analogue start point : -12.4...187.4 mbar: -5...75.2 inH2O: -1.24...18.74 kPa; Analogue end point : 50...250 mbar: 20.1...100.4 inH2O: 5...25 kPa; In steps of : 0.2 mbar: 0.1 inH2O: 0.02 kPa; Factory setting : SP1 = 62.4 mbar: rP1 = 57.4 mbar | SP2 = 187.4 mbar: rP2 = 182.4 mbar | ASP = 0.0 mbar: AEP = 250.0 mbar; Switch point accuracy [% of the span] : < ± 0,2; (Turn down 1:1); Repeatability [% of the span] : < ± 0,1; (with temperature fluctuations < 10 K; Turn down 1:1); Characteristics deviation [% of the span] : < ± 0,2; (Turn down 1:1 , linearity, incl. hysteresis and repeatability , limit value setting to DIN EN IEC 62828-1); Linearity deviation [% of the span] : < ± 0,15; (Turn down 1:1); Hysteresis deviation [% of the span] : < ± 0,15; (Turn down 1:1); Long-term stability [% of the span] : < ± 0,1; (Turn down 1:1; per year); Temperature coefficient zero point [% of the span / 10 K] : < ± 0,05; (0...70 °C); Temperature coefficient span [% of the span / 10 K] : < ± 0,15; (0...70 °C); Damping for the switching output dAP [s] : 0...30; Damping for the analogue output dAA [s] : 0.01...99.99; Communication interface : IO-Link; Transmission type : COM2 (38,4 kBaud); IO-Link revision : 1.0; Profiles : no profile; SIO mode : yes; Required master port type : A; Process data analogue : 1; Process data binary : 2; Min. process cycle time [ms] : 2.3; Supported DeviceIDs : Type of operation: DeviceID | Default: 257; Ambient temperature [°C] : -25...80; Storage temperature [°C] : -40...100; Materials : stainless steel (1.4404 / 316L); FKM; PTFE; PBT; PEI; PFA; Materials (wetted parts) : ceramics (99.9 % Al2O3); stainless steel (1.4435 / 316L); surface characteristics: Ra < 0,4 / Rz 4; PTFE; Min. pressure cycles : 100 million; Process connection : threaded connection G 1 external thread sealing cone - Attention: The unit must only be installed in a process connection for G1 sealing cone.; The G1A sealing cone of the unit is only suited for adapters with metal end stop.; Display unit : mbar; kPa; inH2O; mmWS; % of the span

Flush pressure sensor with display; Min. insulation resistance [MΩ] : 100; (500 V DC); Protection class : III; Reverse polarity protection : yes; Integrated watchdog : yes; Step response time analogue output [ms] : 45; Min. response time of switching output (dAP) [ms] : 3; Step response time analogue output [ms] : 7; Total number of outputs : 2; Output signal : switching signal; analogue signal; IO-Link; (configurable); Electrical design : PNP/NPN; Number of digital outputs : 2; Output function : normally open / normally closed; (parameterisable); Number of analogue outputs : 1; Analogue current output [mA] : 4...20, invertible; (scalable); Short-circuit protection : yes; Type of short-circuit protection : pulsed; Overload protection : yes; Measuring range : -1...4 bar: -14.5...58 psi: -100...400 kPa; Set point SP : -0.99...4 bar: -14.35...58 psi: -99...400 kPa; Reset point rP : -1...3.99 bar: -14.5...57.85 psi: -100...399 kPa; Analogue start point : -1...3 bar: -14.5...43.5 psi: -100...300 kPa; Analogue end point : 0...4 bar: 0...58 psi: 0...400 kPa; In steps of : 0.005 bar: 0.05 psi: 0.5 kPa; Factory setting : SP1 = 1.000 bar: rP1 = 0.920 bar | SP2 = 3.000 bar: rP2 = 2.920 bar | ASP = 0.000 bar: AEP = 4.000 bar; Switch point accuracy [% of the span] : < ± 0,2; (Turn down 1:1); Repeatability [% of the span] : < ± 0,1; (with temperature fluctuations < 10 K; Turn down 1:1); Characteristics deviation [% of the span] : < ± 0,2; (Turn down 1:1 , linearity, incl. hysteresis and repeatability , limit value setting to DIN EN IEC 62828-1); Linearity deviation [% of the span] : < ± 0,15; (Turn down 1:1); Hysteresis deviation [% of the span] : < ± 0,15; (Turn down 1:1); Long-term stability [% of the span] : < ± 0,1; (Turn down 1:1; per year); Temperature coefficient zero point [% of the span / 10 K] : < ± 0,05; (0...70 °C); Temperature coefficient span [% of the span / 10 K] : < ± 0,15; (0...70 °C); Damping for the switching output dAP [s] : 0...30; Damping for the analogue output dAA [s] : 0.01...99.99; Communication interface : IO-Link; Transmission type : COM2 (38,4 kBaud); IO-Link revision : 1.0; Profiles : no profile; SIO mode : yes; Required master port type : A; Process data analogue : 1; Process data binary : 2; Min. process cycle time [ms] : 2.3; Supported DeviceIDs : Type of operation: DeviceID | Default: 158; Ambient temperature [°C] : -25...80; Storage temperature [°C] : -40...100; Materials : stainless steel (1.4404 / 316L); FKM; PTFE; PBT; PEI; PFA; Materials (wetted parts) : ceramics (99.9 % Al2O3); stainless steel (1.4435 / 316L); surface characteristics: Ra < 0,4 / Rz 4; PTFE; Min. pressure cycles : 100 million; Process connection : threaded connection G 1 external thread sealing cone - Attention: The unit must only be installed in a process connection for G1 sealing cone.; The G1A sealing cone of the unit is only suited for adapters with metal end stop.; Display unit : bar; psi; kPa; % of the span

Flush pressure sensor with display; Min. insulation resistance [MΩ] : 100; (500 V DC); Protection class : III; Reverse polarity protection : yes; Measuring principle : hydrostatic; Integrated watchdog : yes; Step response time analogue output [ms] : 45; Min. response time of switching output (dAP) [ms] : 3; Step response time analogue output [ms] : 7; Total number of outputs : 2; Output signal : switching signal; analogue signal; IO-Link; (configurable); Electrical design : PNP/NPN; Number of digital outputs : 2; Output function : normally open / normally closed; (parameterisable); Number of analogue outputs : 1; Analogue current output [mA] : 4...20, invertible; (scalable); Short-circuit protection : yes; Type of short-circuit protection : pulsed; Overload protection : yes; Measuring range : -0.0124...0.25 bar: -12.4...250 mbar: -5...100.4 inH2O: -1.24...25 kPa; Set point SP : -12...250 mbar: -4.8...100.4 inH2O: -1.2...25 kPa; Reset point rP : -12.4...249.6 mbar: -5...100.2 inH2O: -1.24...24.96 kPa; Analogue start point : -12.4...187.4 mbar: -5...75.2 inH2O: -1.24...18.74 kPa; Analogue end point : 50...250 mbar: 20.1...100.4 inH2O: 5...25 kPa; In steps of : 0.2 mbar: 0.1 inH2O: 0.02 kPa; Factory setting : SP1 = 62.4 mbar: rP1 = 57.4 mbar | SP2 = 187.4 mbar: rP2 = 182.4 mbar | ASP = 0.0 mbar: AEP = 250.0 mbar; Switch point accuracy [% of the span] : < ± 0,2; (Turn down 1:1); Repeatability [% of the span] : < ± 0,1; (with temperature fluctuations < 10 K; Turn down 1:1); Characteristics deviation [% of the span] : < ± 0,2; (Turn down 1:1 , linearity, incl. hysteresis and repeatability , limit value setting to DIN EN IEC 62828-1); Linearity deviation [% of the span] : < ± 0,15; (Turn down 1:1); Hysteresis deviation [% of the span] : < ± 0,15; (Turn down 1:1); Long-term stability [% of the span] : < ± 0,1; (Turn down 1:1; per year); Temperature coefficient zero point [% of the span / 10 K] : < ± 0,05; (0...70 °C); Temperature coefficient span [% of the span / 10 K] : < ± 0,15; (0...70 °C); Damping for the switching output dAP [s] : 0...30; Damping for the analogue output dAA [s] : 0.01...99.99; Communication interface : IO-Link; Transmission type : COM2 (38,4 kBaud); IO-Link revision : 1.0; Profiles : no profile; SIO mode : yes; Required master port type : A; Process data analogue : 1; Process data binary : 2; Min. process cycle time [ms] : 2.3; Supported DeviceIDs : Type of operation: DeviceID | Default: 257; Ambient temperature [°C] : -25...80; Storage temperature [°C] : -40...100; Materials : stainless steel (1.4404 / 316L); FKM; PTFE; PBT; PEI; PFA; Materials (wetted parts) : ceramics (99.9 % Al2O3); stainless steel (1.4435 / 316L); surface characteristics: Ra < 0,4 / Rz 4; PTFE; Min. pressure cycles : 100 million; Process connection : threaded connection G 1 external thread Aseptoflex Vario; Display unit : mbar; kPa; inH2O; mmWS; % of the span

Flush pressure sensor with display; Min. insulation resistance [MΩ] : 100; (500 V DC); Protection class : III; Reverse polarity protection : yes; Measuring principle : hydrostatic; Integrated watchdog : yes; Step response time analogue output [ms] : 45; Min. response time of switching output (dAP) [ms] : 3; Step response time analogue output [ms] : 7; Total number of outputs : 2; Output signal : switching signal; analogue signal; IO-Link; (configurable); Electrical design : PNP/NPN; Number of digital outputs : 2; Output function : normally open / normally closed; (parameterisable); Number of analogue outputs : 1; Analogue current output [mA] : 4...20, invertible; (scalable); Short-circuit protection : yes; Type of short-circuit protection : pulsed; Overload protection : yes; Measuring range : -0.124...2.5 bar: -124...2500 mbar: -1.8...36.27 psi: -12.4...250 kPa; Set point SP : -0.12...2.5 bar: -1.74...36.27 psi: -12...250 kPa; Reset point rP : -0.124...2.496 bar: -1.8...36.21 psi: -12.4...249.6 kPa; Analogue start point : -0.124...1.88 bar: -1.8...27.27 psi: -12.4...188 kPa; Analogue end point : 0.5...2.5 bar: 7.26...36.27 psi: 50...250 kPa; In steps of : 0.002 bar: 0.03 psi: 0.2 kPa; Factory setting : SP1 = 0.624 bar: rP1 = 0.574 bar | SP2 = 1.874 bar: rP2 = 1.824 bar | ASP = 0.000 bar: AEP = 2.500 bar; Switch point accuracy [% of the span] : < ± 0,2; (Turn down 1:1); Repeatability [% of the span] : < ± 0,1; (with temperature fluctuations < 10 K; Turn down 1:1); Characteristics deviation [% of the span] : < ± 0,2; (Turn down 1:1 , linearity, incl. hysteresis and repeatability , limit value setting to DIN EN IEC 62828-1); Linearity deviation [% of the span] : < ± 0,15; (Turn down 1:1); Hysteresis deviation [% of the span] : < ± 0,15; (Turn down 1:1); Long-term stability [% of the span] : < ± 0,1; (Turn down 1:1; per year); Temperature coefficient zero point [% of the span / 10 K] : < ± 0,05; (0...70 °C); Temperature coefficient span [% of the span / 10 K] : < ± 0,15; (0...70 °C); Damping for the switching output dAP [s] : 0...30; Damping for the analogue output dAA [s] : 0.01...99.99; Communication interface : IO-Link; Transmission type : COM2 (38,4 kBaud); IO-Link revision : 1.0; Profiles : no profile; SIO mode : yes; Required master port type : A; Process data analogue : 1; Process data binary : 2; Min. process cycle time [ms] : 2.3; Supported DeviceIDs : Type of operation: DeviceID | Default: 159; Ambient temperature [°C] : -25...80; Storage temperature [°C] : -40...100; Materials : stainless steel (1.4404 / 316L); FKM; PTFE; PBT; PEI; PFA; Materials (wetted parts) : ceramics (99.9 % Al2O3); stainless steel (1.4435 / 316L); surface characteristics: Ra < 0,4 / Rz 4; PTFE; Min. pressure cycles : 100 million; Process connection : threaded connection G 1 external thread Aseptoflex Vario; Display unit : bar; kPa; psi; inH2O; mWS; % of the span

Flush pressure sensor with display; Min. insulation resistance [MΩ] : 100; (500 V DC); Protection class : III; Reverse polarity protection : yes; Integrated watchdog : yes; Step response time analogue output [ms] : 45; Min. response time of switching output (dAP) [ms] : 3; Step response time analogue output [ms] : 7; Total number of outputs : 2; Output signal : switching signal; analogue signal; IO-Link; (configurable); Electrical design : PNP/NPN; Number of digital outputs : 2; Output function : normally open / normally closed; (parameterisable); Number of analogue outputs : 1; Analogue current output [mA] : 4...20, invertible; (scalable); Short-circuit protection : yes; Type of short-circuit protection : pulsed; Overload protection : yes; Measuring range : -1...4 bar: -14.5...58 psi: -100...400 kPa; Set point SP : -0.99...4 bar: -14.35...58 psi: -99...400 kPa; Reset point rP : -1...3.99 bar: -14.5...57.85 psi: -100...399 kPa; Analogue start point : -1...3 bar: -14.5...43.5 psi: -100...300 kPa; Analogue end point : 0...4 bar: 0...58 psi: 0...400 kPa; In steps of : 0.005 bar: 0.05 psi: 0.5 kPa; Factory setting : SP1 = 1.000 bar: rP1 = 0.920 bar | SP2 = 3.000 bar: rP2 = 2.920 bar | ASP = 0.000 bar: AEP = 4.000 bar; Switch point accuracy [% of the span] : < ± 0,2; (Turn down 1:1); Repeatability [% of the span] : < ± 0,1; (with temperature fluctuations < 10 K; Turn down 1:1); Characteristics deviation [% of the span] : < ± 0,2; (Turn down 1:1 , linearity, incl. hysteresis and repeatability , limit value setting to DIN EN IEC 62828-1); Linearity deviation [% of the span] : < ± 0,15; (Turn down 1:1); Hysteresis deviation [% of the span] : < ± 0,15; (Turn down 1:1); Long-term stability [% of the span] : < ± 0,1; (Turn down 1:1; per year); Temperature coefficient zero point [% of the span / 10 K] : < ± 0,05; (0...70 °C); Temperature coefficient span [% of the span / 10 K] : < ± 0,15; (0...70 °C); Damping for the switching output dAP [s] : 0...30; Damping for the analogue output dAA [s] : 0.01...99.99; Communication interface : IO-Link; Transmission type : COM2 (38,4 kBaud); IO-Link revision : 1.0; Profiles : no profile; SIO mode : yes; Required master port type : A; Process data analogue : 1; Process data binary : 2; Min. process cycle time [ms] : 2.3; Supported DeviceIDs : Type of operation: DeviceID | Default: 158; Ambient temperature [°C] : -25...80; Storage temperature [°C] : -40...100; Materials : stainless steel (1.4404 / 316L); FKM; PTFE; PBT; PEI; PFA; Materials (wetted parts) : ceramics (99.9 % Al2O3); stainless steel (1.4435 / 316L); surface characteristics: Ra < 0,4 / Rz 4; PTFE; Min. pressure cycles : 100 million; Process connection : threaded connection G 1 external thread Aseptoflex Vario; Display unit : bar; psi; kPa; % of the span

Flush pressure sensor with display; Min. insulation resistance [MΩ] : 100; (500 V DC); Protection class : III; Reverse polarity protection : yes; Integrated watchdog : yes; Step response time analogue output [ms] : 45; Min. response time of switching output (dAP) [ms] : 3; Step response time analogue output [ms] : 7; Total number of outputs : 2; Output signal : switching signal; analogue signal; IO-Link; (configurable); Electrical design : PNP/NPN; Number of digital outputs : 2; Output function : normally open / normally closed; (parameterisable); Number of analogue outputs : 1; Analogue current output [mA] : 4...20, invertible; (scalable); Short-circuit protection : yes; Type of short-circuit protection : pulsed; Overload protection : yes; Measuring range : -1...10 bar: -14.5...145 psi: -0.1...1 MPa; Set point SP : -0.98...10 bar: -14.2...145 psi: -0.098...1 MPa; Reset point rP : -1...9.98 bar: -14.5...144.7 psi: -0.1...0.998 MPa; Analogue start point : -1...7.5 bar: -14.5...108.7 psi: -0.1...0.75 MPa; Analogue end point : 1.5...10 bar: 21.8...145 psi: 0.15...1 MPa; In steps of : 0.01 bar: 0.1 psi: 0.001 MPa; Factory setting : SP1 = 2.50 bar: rP1 = 2.30 bar | SP2 = 7.50 bar: rP2 = 7.30 bar | ASP = 0.00 bar: AEP = 10.00 bar; Switch point accuracy [% of the span] : < ± 0,2; (Turn down 1:1); Repeatability [% of the span] : < ± 0,1; (with temperature fluctuations < 10 K; Turn down 1:1); Characteristics deviation [% of the span] : < ± 0,2; (Turn down 1:1 , linearity, incl. hysteresis and repeatability , limit value setting to DIN EN IEC 62828-1); Linearity deviation [% of the span] : < ± 0,15; (Turn down 1:1); Hysteresis deviation [% of the span] : < ± 0,15; (Turn down 1:1); Long-term stability [% of the span] : < ± 0,1; (Turn down 1:1; per year); Temperature coefficient zero point [% of the span / 10 K] : < ± 0,05; (0...70 °C); Temperature coefficient span [% of the span / 10 K] : < ± 0,15; (0...70 °C); Damping for the switching output dAP [s] : 0...30; Damping for the analogue output dAA [s] : 0.01...99.99; Communication interface : IO-Link; Transmission type : COM2 (38,4 kBaud); IO-Link revision : 1.0; Profiles : no profile; SIO mode : yes; Required master port type : A; Process data analogue : 1; Process data binary : 2; Min. process cycle time [ms] : 2.3; Supported DeviceIDs : Type of operation: DeviceID | Default: 157; Ambient temperature [°C] : -25...80; Storage temperature [°C] : -40...100; Materials : stainless steel (1.4404 / 316L); FKM; PTFE; PBT; PEI; PFA; Materials (wetted parts) : ceramics (99.9 % Al2O3); stainless steel (1.4435 / 316L); surface characteristics: Ra < 0,4 / Rz 4; PTFE; Min. pressure cycles : 100 million; Process connection : threaded connection G 1 external thread Aseptoflex Vario; Display unit : bar; psi; MPa; % of the span

Flush pressure sensor with display; Min. insulation resistance [MΩ] : 100; (500 V DC); Protection class : III; Reverse polarity protection : yes; Measuring principle : hydrostatic; Integrated watchdog : yes; Step response time analogue output [ms] : 45; Min. response time of switching output (dAP) [ms] : 3; Step response time analogue output [ms] : 7; Total number of outputs : 2; Output signal : switching signal; analogue signal; IO-Link; (configurable); Electrical design : PNP/NPN; Number of digital outputs : 2; Output function : normally open / normally closed; (parameterisable); Number of analogue outputs : 1; Analogue current output [mA] : 4...20, invertible; (scalable); Short-circuit protection : yes; Type of short-circuit protection : pulsed; Overload protection : yes; Measuring range : -0.05...1 bar: -50...1000 mbar: -0.73...14.5 psi: -5...100 kPa; Set point SP : -48...1000 mbar: -0.7...14.5 psi: -4.8...100 kPa; Reset point rP : -50...998 mbar: -0.73...14.47 psi: -0.5...99.8 kPa; Analogue start point : -50...750 mbar: -0.73...10.88 psi: -5...75 kPa; Analogue end point : 200...1000 mbar: 2.9...14.5 psi: 20...100 kPa; In steps of : 1 mbar: 0.01 psi: 0.1 kPa; Factory setting : SP1 = 250 mbar: rP1 = 230 mbar | SP2 = 750 mbar: rP2 = 730 mbar | ASP = 0 mbar: AEP = 1000 mbar; Switch point accuracy [% of the span] : < ± 0,2; (Turn down 1:1); Repeatability [% of the span] : < ± 0,1; (with temperature fluctuations < 10 K; Turn down 1:1); Characteristics deviation [% of the span] : < ± 0,2; (Turn down 1:1 , linearity, incl. hysteresis and repeatability , limit value setting to DIN EN IEC 62828-1); Linearity deviation [% of the span] : < ± 0,15; (Turn down 1:1); Hysteresis deviation [% of the span] : < ± 0,15; (Turn down 1:1); Long-term stability [% of the span] : < ± 0,1; (Turn down 1:1; per year); Temperature coefficient zero point [% of the span / 10 K] : < ± 0,05; (0...70 °C); Temperature coefficient span [% of the span / 10 K] : < ± 0,15; (0...70 °C); Damping for the switching output dAP [s] : 0...30; Damping for the analogue output dAA [s] : 0.01...99.99; Communication interface : IO-Link; Transmission type : COM2 (38,4 kBaud); IO-Link revision : 1.0; Profiles : no profile; SIO mode : yes; Required master port type : A; Process data analogue : 1; Process data binary : 2; Min. process cycle time [ms] : 2.3; Supported DeviceIDs : Type of operation: DeviceID | Default: 256; Ambient temperature [°C] : -25...80; Storage temperature [°C] : -40...100; Materials : stainless steel (1.4404 / 316L); FKM; PTFE; PBT; PEI; PFA; Materials (wetted parts) : ceramics (99.9 % Al2O3); stainless steel (1.4435 / 316L); surface characteristics: Ra < 0,4 / Rz 4; PTFE; Min. pressure cycles : 100 million; Process connection : threaded connection G 1 external thread sealing cone - Attention: The unit must only be installed in a process connection for G1 sealing cone.; The G1A sealing cone of the unit is only suited for adapters with metal end stop.; Display unit : mbar; kPa; psi; inH2O; mWS; % of the span

Combined pressure sensor; Min. insulation resistance [MΩ] : 100; (500 V DC); Protection class : III; Reverse polarity protection : yes; Integrated watchdog : yes; Step response time analogue output [ms] : 45; Min. response time of switching output (dAP) [ms] : 3; Step response time analogue output [ms] : 7; Total number of outputs : 2; Output signal : switching signal; analogue signal; IO-Link; (configurable); Electrical design : PNP/NPN; Number of digital outputs : 2; Output function : normally open / normally closed; (parameterisable); Number of analogue outputs : 1; Analogue current output [mA] : 4...20, invertible; (scalable); Short-circuit protection : yes; Type of short-circuit protection : pulsed; Overload protection : yes; Measuring range : -1...6 bar: -14.5...87 psi: -100...600 kPa; Set point SP : -0.99...6 bar: -14.4...87 psi: -99...600 kPa; Reset point rP : -1...5.99 bar: -14.5...86.9 psi: -100...599 kPa; Analogue start point : -1...4.5 bar: -14.5...65.3 psi: -100...450 kPa; Analogue end point : 0.5...6 bar: 7.3...87 psi: 50...600 kPa; In steps of : 0.005 bar: 0.1 psi: 0.5 kPa; Factory setting : SP1 = 1.5 bar: rP1 = 1.38 bar | SP2 = 4.5 bar: rP2 = 4.380 bar | ASP = 0.0 bar: AEP = 6.0 bar; Switch point accuracy [% of the span] : < ± 0,2; (Turn down 1:1); Repeatability [% of the span] : < ± 0,1; (with temperature fluctuations < 10 K; Turn down 1:1); Characteristics deviation [% of the span] : < ± 0,2; (Turn down 1:1 , linearity, incl. hysteresis and repeatability , limit value setting to DIN EN IEC 62828-1); Linearity deviation [% of the span] : < ± 0,15; (Turn down 1:1); Hysteresis deviation [% of the span] : < ± 0,15; (Turn down 1:1); Long-term stability [% of the span] : < ± 0,1; (Turn down 1:1; per year); Temperature coefficient zero point [% of the span / 10 K] : < ± 0,05; (0...70 °C); Temperature coefficient span [% of the span / 10 K] : < ± 0,15; (0...70 °C); Damping for the switching output dAP [s] : 0...30; Damping for the analogue output dAA [s] : 0.01...99.99; Communication interface : IO-Link; Transmission type : COM2 (38,4 kBaud); IO-Link revision : 1.0; Profiles : no profile; SIO mode : yes; Required master port type : A; Process data analogue : 1; Process data binary : 2; Min. process cycle time [ms] : 2.3; Supported DeviceIDs : Type of operation: DeviceID | Default: 728; Ambient temperature [°C] : -25...80; Storage temperature [°C] : -40...100; Materials : stainless steel (1.4404 / 316L); FKM; PTFE; PBT; PEI; PFA; Materials (wetted parts) : ceramics (99.9 % Al2O3); stainless steel (1.4435 / 316L); surface characteristics: Ra < 0,4 / Rz 4; PTFE; Min. pressure cycles : 100 million; Process connection : threaded connection G 1 external thread Aseptoflex Vario; Display unit : bar; kPa; psi; % of the span

Combined pressure sensor; Min. insulation resistance [MΩ] : 100; (500 V DC); Protection class : III; Reverse polarity protection : yes; Integrated watchdog : yes; Step response time analogue output [ms] : 45; Min. response time of switching output (dAP) [ms] : 3; Step response time analogue output [ms] : 7; Total number of outputs : 2; Output signal : switching signal; analogue signal; IO-Link; (configurable); Electrical design : PNP/NPN; Number of digital outputs : 2; Output function : normally open / normally closed; (parameterisable); Number of analogue outputs : 1; Analogue current output [mA] : 4...20, invertible; (scalable); Short-circuit protection : yes; Type of short-circuit protection : pulsed; Overload protection : yes; Measuring range : -1...16 bar: -14.6...232 psi: -0.1...1.6 MPa; Set point SP : -0.98...16 bar: -14.2...232 psi: -0.098...1.6 MPa; Reset point rP : -1...15.98 bar: -14.6...231.6 psi: -0.1...1.598 MPa; Analogue start point : -1...12 bar: -14.6...174 psi: -0.1...1.2 MPa; Analogue end point : 3...16 bar: 43.6...232 psi: 0.3...1.6 MPa; In steps of : 0.02 bar: 0.2 psi: 0.002 MPa; Factory setting : SP1 = 4.0 bar: rP1 = 3.68 bar | SP2 = 12.0 bar: rP2 = 11.68 bar | ASP = 0.0 bar: AEP = 16.0 bar; Switch point accuracy [% of the span] : < ± 0,2; (Turn down 1:1); Repeatability [% of the span] : < ± 0,1; (with temperature fluctuations < 10 K; Turn down 1:1); Characteristics deviation [% of the span] : < ± 0,2; (Turn down 1:1 , linearity, incl. hysteresis and repeatability , limit value setting to DIN EN IEC 62828-1); Linearity deviation [% of the span] : < ± 0,15; (Turn down 1:1); Hysteresis deviation [% of the span] : < ± 0,15; (Turn down 1:1); Long-term stability [% of the span] : < ± 0,1; (Turn down 1:1; per year); Temperature coefficient zero point [% of the span / 10 K] : < ± 0,05; (0...70 °C); Temperature coefficient span [% of the span / 10 K] : < ± 0,15; (0...70 °C); Damping for the switching output dAP [s] : 0...30; Damping for the analogue output dAA [s] : 0.01...99.99; Communication interface : IO-Link; Transmission type : COM2 (38,4 kBaud); IO-Link revision : 1.0; Profiles : no profile; SIO mode : yes; Required master port type : A; Process data analogue : 1; Process data binary : 2; Min. process cycle time [ms] : 2.3; Supported DeviceIDs : Type of operation: DeviceID | Default: 729; Ambient temperature [°C] : -25...80; Storage temperature [°C] : -40...100; Materials : stainless steel (1.4404 / 316L); FKM; PTFE; PBT; PEI; PFA; Materials (wetted parts) : ceramics (99.9 % Al2O3); stainless steel (1.4435 / 316L); surface characteristics: Ra < 0,4 / Rz 4; PTFE; Min. pressure cycles : 100 million; Process connection : threaded connection G 1 external thread Aseptoflex Vario; Display unit : bar; MPa; psi; % of the span

Combined pressure sensor; Min. insulation resistance [MΩ] : 100; (500 V DC); Protection class : III; Reverse polarity protection : yes; Integrated watchdog : yes; Step response time analogue output [ms] : 45; Min. response time of switching output (dAP) [ms] : 3; Step response time analogue output [ms] : 7; Total number of outputs : 2; Output signal : switching signal; analogue signal; IO-Link; (configurable); Electrical design : PNP/NPN; Number of digital outputs : 2; Output function : normally open / normally closed; (parameterisable); Number of analogue outputs : 1; Analogue current output [mA] : 4...20, invertible; (scalable); Short-circuit protection : yes; Type of short-circuit protection : pulsed; Overload protection : yes; Measuring range : -0.1...1.6 bar: -100...1600 mbar: -1.46...23.2 psi: -10...160 kPa; Set point SP : -96...1600 mbar: -1.4...23.2 psi: -9.6...160 kPa; Reset point rP : -100...1598 mbar: -1.44...23.16 psi: -10...159.8 kPa; Analogue start point : -100...1200 mbar: -1.46...17.42 psi: -10...120 kPa; Analogue end point : 300...1600 mbar: 4.34...23.2 psi: 30...160 kPa; In steps of : 2 mbar: 0.02 psi: 0.2 kPa; Factory setting : SP1 = 0.4 bar: rP1 = 0.368 bar | SP2 = 1.2 bar: rP2 = 1.168 bar | ASP = 0.0 bar: AEP = 1.6 bar; Switch point accuracy [% of the span] : < ± 0,2; (Turn down 1:1); Repeatability [% of the span] : < ± 0,1; (with temperature fluctuations < 10 K; Turn down 1:1); Characteristics deviation [% of the span] : < ± 0,2; (Turn down 1:1 , linearity, incl. hysteresis and repeatability , limit value setting to DIN EN IEC 62828-1); Linearity deviation [% of the span] : < ± 0,15; (Turn down 1:1); Hysteresis deviation [% of the span] : < ± 0,15; (Turn down 1:1); Long-term stability [% of the span] : < ± 0,1; (Turn down 1:1; per year); Temperature coefficient zero point [% of the span / 10 K] : < ± 0,05; (0...70 °C); Temperature coefficient span [% of the span / 10 K] : < ± 0,15; (0...70 °C); Damping for the switching output dAP [s] : 0...30; Damping for the analogue output dAA [s] : 0.01...99.99; Communication interface : IO-Link; Transmission type : COM2 (38,4 kBaud); IO-Link revision : 1.0; Profiles : no profile; SIO mode : yes; Required master port type : A; Process data analogue : 1; Process data binary : 2; Min. process cycle time [ms] : 2.3; Supported DeviceIDs : Type of operation: DeviceID | Default: 727; Ambient temperature [°C] : -25...80; Storage temperature [°C] : -40...100; Materials : stainless steel (1.4404 / 316L); FKM; PTFE; PBT; PEI; PFA; Materials (wetted parts) : ceramics (99.9 % Al2O3); stainless steel (1.4435 / 316L); surface characteristics: Ra < 0,4 / Rz 4; PTFE; Min. pressure cycles : 100 million; Process connection : threaded connection G 1 external thread Aseptoflex Vario; Display unit : mbar; kPa; psi; inH2O; mWS; % of the span

Combined pressure sensor; Min. insulation resistance [MΩ] : 100; (500 V DC); Protection class : III; Reverse polarity protection : yes; Integrated watchdog : yes; Step response time analogue output [ms] : 45; Min. response time of switching output (dAP) [ms] : 3; Step response time analogue output [ms] : 7; Total number of outputs : 2; Output signal : switching signal; analogue signal; IO-Link; (configurable); Electrical design : PNP/NPN; Number of digital outputs : 2; Output function : normally open / normally closed; (parameterisable); Number of analogue outputs : 1; Analogue current output [mA] : 4...20, invertible; (scalable); Short-circuit protection : yes; Type of short-circuit protection : pulsed; Overload protection : yes; Measuring range : -1...6 bar: -14.5...87 psi: -100...600 kPa; Set point SP : -0.99...6 bar: -14.4...87 psi: -99...600 kPa; Reset point rP : -1...5.99 bar: -14.5...86.9 psi: -100...599 kPa; Analogue start point : -1...4.5 bar: -14.5...65.3 psi: -100...450 kPa; Analogue end point : 0.5...6 bar: 7.3...87 psi: 50...600 kPa; In steps of : 0.005 bar: 0.1 psi: 0.5 kPa; Factory setting : SP1 = 1.5 bar: rP1 = 1.38 bar | SP2 = 4.5 bar: rP2 = 4.380 bar | ASP = 0.0 bar: AEP = 6.0 bar; Switch point accuracy [% of the span] : < ± 0,2; (Turn down 1:1); Repeatability [% of the span] : < ± 0,1; (with temperature fluctuations < 10 K; Turn down 1:1); Characteristics deviation [% of the span] : < ± 0,2; (Turn down 1:1 , linearity, incl. hysteresis and repeatability , limit value setting to DIN EN IEC 62828-1); Linearity deviation [% of the span] : < ± 0,15; (Turn down 1:1); Hysteresis deviation [% of the span] : < ± 0,15; (Turn down 1:1); Long-term stability [% of the span] : < ± 0,1; (Turn down 1:1; per year); Temperature coefficient zero point [% of the span / 10 K] : < ± 0,05; (0...70 °C); Temperature coefficient span [% of the span / 10 K] : < ± 0,15; (0...70 °C); Damping for the switching output dAP [s] : 0...30; Damping for the analogue output dAA [s] : 0.01...99.99; Communication interface : IO-Link; Transmission type : COM2 (38,4 kBaud); IO-Link revision : 1.0; Profiles : no profile; SIO mode : yes; Required master port type : A; Process data analogue : 1; Process data binary : 2; Min. process cycle time [ms] : 2.3; Supported DeviceIDs : Type of operation: DeviceID | Default: 728; Ambient temperature [°C] : -25...80; Storage temperature [°C] : -40...100; Materials : stainless steel (1.4404 / 316L); FKM; PTFE; PBT; PEI; PFA; Materials (wetted parts) : ceramics (99.9 % Al2O3); stainless steel (1.4435 / 316L); surface characteristics: Ra < 0,4 / Rz 4; PTFE; Min. pressure cycles : 100 million; Process connection : threaded connection G 1 external thread sealing cone - Attention: The unit must only be installed in a process connection for G1 sealing cone.; The G1A sealing cone of the unit is only suited for adapters with metal end stop.; Display unit : bar; kPa; psi; % of the span