Ifm – PV7604

Pressure switch with IO-Link; Operating voltage [V] : 18...30 DC; Min. insulation resistance [MΩ] : 100; (500 V DC); Protection class : III; Reverse polarity protection : yes; Power-on delay time [s] : < 0.3; Total number of outputs : 2; Output signal : switching signal; IO-Link; (configurable); Electrical design : PNP/NPN; Number of digital outputs : 2; Output function : normally open / normally closed; (parameterisable); Max. voltage drop switching output DC [V] : 2; Permanent current rating of switching output DC [mA] : 100; Switching frequency DC [Hz] : < 170; Short-circuit protection : yes; Type of short-circuit protection : pulsed; Overload protection : yes; Measuring range [MPa] : 0...25; Set point SP [MPa] : 0.25...25; Reset point rP [MPa] : 0.13...24.88; In steps of [MPa] : 0.01; Factory setting : SP1 = 6.25 MPa: rP1 = 5.75 MPa: ou1 = Hno; | SP2 = 18.75 MPa: rP2 = 18.25 MPa: ou2 = Hno; | dS1/dS2 = 0 ms: dr1/dr2 = 0 ms | coF = 0 %: P-n = PnP: dAP= 60 ms; Switch point accuracy [% of the span] : < ± 0,5 (nach DIN EN 61298-2); Repeatability [% of the span] : < ± 0,05; (with temperature fluctuations < 10 K); Characteristics deviation [% of the span] : < ± 0,5; (linearity incl. hysteresis and repeatability, limit value setting to DIN EN IEC 62828-1); Linearity deviation [% of the span] : < ± 0,1 (BFSL) / < ± 0,2 (LS); Hysteresis deviation [% of the span] : < ± 0,2; Long-term stability [% of the span] : < ± 0,1; (per 6 months); Temperature coefficient zero point [% of the span / 10 K] : < 0,1 (-25...90 °C) / < 0,2 (-40...-25 °C); Temperature coefficient span [% of the span / 10 K] : < 0,1 (-25...90 °C) / < 0,2 (-40...-25 °C); Response time [ms] : < 3; Parameter setting options : hysteresis / window; normally open / normally closed; switching logic; switch-on/switch-off delay; Damping; Communication interface : IO-Link; Transmission type : COM2 (38,4 kBaud); IO-Link revision : 1.1; SDCI standard : IEC 61131-9; Profiles : Smart Sensor: Process Data Variable; Device Identification, Device Diagnosis; SIO mode : yes; Required master port type : A; Process data analogue : 2; Process data binary : 2; Min. process cycle time [ms] : 5; Supported DeviceIDs : Type of operation: DeviceID | Default: 781; Ambient temperature [°C] : -40...90; Storage temperature [°C] : -40...100; Materials : 1.4542 (17-4 PH / 630); stainless steel (1.4404 / 316L); PEI; Materials (wetted parts) : stainless steel (1.4305 / 303); 1.4542 (17-4 PH / 630); Min. pressure cycles : 60 million; (at 1.2 times nominal pressure); Tightening torque [Nm] : 50; (recommended tightening torque; depends on lubrication, seal and pressure rating); Process connection : threaded connection R 1/4 external thread internal thread:M5; Restrictor element integrated : yes

Electronic pressure monitor; Operating voltage [V] : 18...30 DC; Min. insulation resistance [MΩ] : 100; (500 V DC); Protection class : III; Reverse polarity protection : yes; Power-on delay time [s] : < 0.3; Total number of outputs : 2; Output signal : switching signal; IO-Link; (configurable); Electrical design : PNP/NPN; Number of digital outputs : 2; Output function : normally open / normally closed; (parameterisable); Max. voltage drop switching output DC [V] : 2; Permanent current rating of switching output DC [mA] : 100; Switching frequency DC [Hz] : < 170; Short-circuit protection : yes; Type of short-circuit protection : pulsed; Overload protection : yes; Measuring range : 0...60 bar: 0...870 psi: 0...6 MPa; Set point SP : 0.6...60 bar: 9...870 psi: 0.06...6 MPa; Reset point rP : 0.3...59.7 bar: 4...866 psi: 0.03...5.97 MPa; In steps of : 0.02 bar: 1 psi: 0.002 MPa; Factory setting : SP1 = 15 bar: rP1 = 13.8 bar: ou1 = Hno; | SP2 = 45 bar: rP2 = 43.8 bar: ou2 = Hno; | dS1/dS2 = 0 ms: dr1/dr2 = 0 ms | coF = 0 %: P-n = PnP: dAP= 60 ms; Switch point accuracy [% of the span] : < ± 0,5 (nach DIN EN 61298-2); Repeatability [% of the span] : < ± 0,05; (with temperature fluctuations < 10 K); Characteristics deviation [% of the span] : < ± 0,5; (linearity incl. hysteresis and repeatability, limit value setting to DIN EN IEC 62828-1); Linearity deviation [% of the span] : < ± 0,1 (BFSL) / < ± 0,2 (LS); Hysteresis deviation [% of the span] : < ± 0,2; Long-term stability [% of the span] : < ± 0,1; (per 6 months); Temperature coefficient zero point [% of the span / 10 K] : < 0,1 (-25...90 °C) / < 0,2 (-40...-25 °C); Temperature coefficient span [% of the span / 10 K] : < 0,1 (-25...90 °C) / < 0,2 (-40...-25 °C); Response time [ms] : < 3; Parameter setting options : hysteresis / window; normally open / normally closed; switching logic; switch-on/switch-off delay; Damping; Communication interface : IO-Link; Transmission type : COM2 (38,4 kBaud); IO-Link revision : 1.1; SDCI standard : IEC 61131-9; Profiles : Smart Sensor: Process Data Variable; Device Identification, Device Diagnosis; SIO mode : yes; Required master port type : A; Process data analogue : 2; Process data binary : 2; Min. process cycle time [ms] : 5; Supported DeviceIDs : Type of operation: DeviceID | Default: 899; Ambient temperature [°C] : -40...90; Storage temperature [°C] : -40...100; Materials : 1.4542 (17-4 PH / 630); stainless steel (1.4404 / 316L); PEI; Materials (wetted parts) : stainless steel (1.4305 / 303); 1.4542 (17-4 PH / 630); Min. pressure cycles : 60 million; (at 1.2 times nominal pressure); Tightening torque [Nm] : 50; (recommended tightening torque; depends on lubrication, seal and pressure rating); Process connection : threaded connection 1/4" NPT external thread internal thread:M5; Restrictor element integrated : yes

Electronic pressure monitor; Operating voltage [V] : 18...30 DC; Min. insulation resistance [MΩ] : 100; (500 V DC); Protection class : III; Reverse polarity protection : yes; Power-on delay time [s] : < 0.3; Total number of outputs : 2; Output signal : switching signal; IO-Link; (configurable); Electrical design : PNP/NPN; Number of digital outputs : 2; Output function : normally open / normally closed; (parameterisable); Max. voltage drop switching output DC [V] : 2; Permanent current rating of switching output DC [mA] : 100; Switching frequency DC [Hz] : < 170; Short-circuit protection : yes; Type of short-circuit protection : pulsed; Overload protection : yes; Measuring range : -1...25 bar: -14.6...362.6 psi: -0.1...2.5 MPa; Set point SP : -0.75...25 bar: -10.8...362.6 psi: -0.075...2.5 MPa; Reset point rP : -0.87...24.88 bar: -12.7...360.8 psi: -0.087...2488 MPa; In steps of : 0.01 bar: 0.1 psi: 0.001 MPa; Factory setting : SP1 = 6.25 bar: rP1 = 5.75 bar: ou1 = Hno; | SP2 = 18.75 bar: rP2 = 18.25 bar: ou2 = Hno; | dS1/dS2 = 0 ms: dr1/dr2 = 0 ms | coF = 0 %: P-n = PnP: dAP= 60 ms; Switch point accuracy [% of the span] : < ± 0,5 (nach DIN EN 61298-2); Repeatability [% of the span] : < ± 0,05; (with temperature fluctuations < 10 K); Characteristics deviation [% of the span] : < ± 0,5; (linearity incl. hysteresis and repeatability, limit value setting to DIN EN IEC 62828-1); Linearity deviation [% of the span] : < ± 0,1 (BFSL) / < ± 0,2 (LS); Hysteresis deviation [% of the span] : < ± 0,2; Long-term stability [% of the span] : < ± 0,1; (per 6 months); Temperature coefficient zero point [% of the span / 10 K] : < 0,1 (-25...90 °C) / < 0,2 (-40...-25 °C); Temperature coefficient span [% of the span / 10 K] : < 0,1 (-25...90 °C) / < 0,2 (-40...-25 °C); Response time [ms] : < 3; Parameter setting options : hysteresis / window; normally open / normally closed; switching logic; switch-on/switch-off delay; Damping; Communication interface : IO-Link; Transmission type : COM2 (38,4 kBaud); IO-Link revision : 1.1; SDCI standard : IEC 61131-9; Profiles : Smart Sensor: Process Data Variable; Device Identification, Device Diagnosis; SIO mode : yes; Required master port type : A; Process data analogue : 2; Process data binary : 2; Min. process cycle time [ms] : 5; Supported DeviceIDs : Type of operation: DeviceID | Default: 854; Ambient temperature [°C] : -40...90; Storage temperature [°C] : -40...100; Materials : 1.4542 (17-4 PH / 630); stainless steel (1.4404 / 316L); PEI; Materials (wetted parts) : stainless steel (1.4305 / 303); 1.4542 (17-4 PH / 630); Min. pressure cycles : 60 million; (at 1.2 times nominal pressure); Tightening torque [Nm] : 50; (recommended tightening torque; depends on lubrication, seal and pressure rating); Process connection : threaded connection 1/4" NPT external thread internal thread:M5; Restrictor element integrated : yes

Electronic pressure monitor; Operating voltage [V] : 18...30 DC; Min. insulation resistance [MΩ] : 100; (500 V DC); Protection class : III; Reverse polarity protection : yes; Power-on delay time [s] : < 0.3; Total number of outputs : 2; Output signal : switching signal; IO-Link; (configurable); Electrical design : PNP/NPN; Number of digital outputs : 2; Output function : normally open / normally closed; (parameterisable); Max. voltage drop switching output DC [V] : 2; Permanent current rating of switching output DC [mA] : 100; Switching frequency DC [Hz] : < 170; Short-circuit protection : yes; Type of short-circuit protection : pulsed; Overload protection : yes; Measuring range : 0...100 bar: 0...1450 psi: 0...10 MPa; Set point SP : 1...100 bar: 15...1450 psi: 0.1...10 MPa; Reset point rP : 0.5...99.5 bar: 7...1443 psi: 0.05...9.95 MPa; In steps of : 0.05 bar: 1 psi: 0.005 MPa; Factory setting : SP1 = 25 bar: rP1 = 23 bar: ou1 = Hno; | SP2 = 75 bar: rP2 = 73 bar: ou2 = Hno; | dS1/dS2 = 0 ms: dr1/dr2 = 0 ms | coF = 0 %: P-n = PnP: dAP= 60 ms; Switch point accuracy [% of the span] : < ± 0,5 (nach DIN EN 61298-2); Repeatability [% of the span] : < ± 0,05; (with temperature fluctuations < 10 K); Characteristics deviation [% of the span] : < ± 0,5; (linearity incl. hysteresis and repeatability, limit value setting to DIN EN IEC 62828-1); Linearity deviation [% of the span] : < ± 0,1 (BFSL) / < ± 0,2 (LS); Hysteresis deviation [% of the span] : < ± 0,2; Long-term stability [% of the span] : < ± 0,1; (per 6 months); Temperature coefficient zero point [% of the span / 10 K] : < 0,1 (-25...90 °C) / < 0,2 (-40...-25 °C); Temperature coefficient span [% of the span / 10 K] : < 0,1 (-25...90 °C) / < 0,2 (-40...-25 °C); Response time [ms] : < 3; Parameter setting options : hysteresis / window; normally open / normally closed; switching logic; switch-on/switch-off delay; Damping; Communication interface : IO-Link; Transmission type : COM2 (38,4 kBaud); IO-Link revision : 1.1; SDCI standard : IEC 61131-9; Profiles : Smart Sensor: Process Data Variable; Device Identification, Device Diagnosis; SIO mode : yes; Required master port type : A; Process data analogue : 2; Process data binary : 2; Min. process cycle time [ms] : 5; Supported DeviceIDs : Type of operation: DeviceID | Default: 853; Ambient temperature [°C] : -40...90; Storage temperature [°C] : -40...100; Materials : 1.4542 (17-4 PH / 630); stainless steel (1.4404 / 316L); PEI; Materials (wetted parts) : stainless steel (1.4305 / 303); 1.4542 (17-4 PH / 630); Min. pressure cycles : 60 million; (at 1.2 times nominal pressure); Tightening torque [Nm] : 50; (recommended tightening torque; depends on lubrication, seal and pressure rating); Process connection : threaded connection 1/4" NPT external thread internal thread:M5; Restrictor element integrated : yes

Electronic pressure monitor; Operating voltage [V] : 18...30 DC; Min. insulation resistance [MΩ] : 100; (500 V DC); Protection class : III; Reverse polarity protection : yes; Power-on delay time [s] : < 0.3; Total number of outputs : 2; Output signal : switching signal; IO-Link; (configurable); Electrical design : PNP/NPN; Number of digital outputs : 2; Output function : normally open / normally closed; (parameterisable); Max. voltage drop switching output DC [V] : 2; Permanent current rating of switching output DC [mA] : 100; Switching frequency DC [Hz] : < 170; Short-circuit protection : yes; Type of short-circuit protection : pulsed; Overload protection : yes; Measuring range : 0...250 bar: 0...3626 psi: 0...25 MPa; Set point SP : 2.5...250 bar: 37...3626 psi: 0.25...25 MPa; Reset point rP : 1.3...248.8 bar: 18...3608 psi: 0.13...24.88 MPa; In steps of : 0.1 bar: 1 psi: 0.01 MPa; Factory setting : SP1 = 62.5 bar: rP1 = 57.5 bar: ou1 = Hno; | SP2 = 187.5 bar: rP2 = 182.5 bar: ou2 = Hno; | dS1/dS2 = 0 ms: dr1/dr2 = 0 ms | coF = 0 %: P-n = PnP: dAP= 60 ms; Switch point accuracy [% of the span] : < ± 0,5 (nach DIN EN 61298-2); Repeatability [% of the span] : < ± 0,05; (with temperature fluctuations < 10 K); Characteristics deviation [% of the span] : < ± 0,5; (linearity incl. hysteresis and repeatability, limit value setting to DIN EN IEC 62828-1); Linearity deviation [% of the span] : < ± 0,1 (BFSL) / < ± 0,2 (LS); Hysteresis deviation [% of the span] : < ± 0,2; Long-term stability [% of the span] : < ± 0,1; (per 6 months); Temperature coefficient zero point [% of the span / 10 K] : < 0,1 (-25...90 °C) / < 0,2 (-40...-25 °C); Temperature coefficient span [% of the span / 10 K] : < 0,1 (-25...90 °C) / < 0,2 (-40...-25 °C); Response time [ms] : < 3; Parameter setting options : hysteresis / window; normally open / normally closed; switching logic; switch-on/switch-off delay; Damping; Communication interface : IO-Link; Transmission type : COM2 (38,4 kBaud); IO-Link revision : 1.1; SDCI standard : IEC 61131-9; Profiles : Smart Sensor: Process Data Variable; Device Identification, Device Diagnosis; SIO mode : yes; Required master port type : A; Process data analogue : 2; Process data binary : 2; Min. process cycle time [ms] : 5; Supported DeviceIDs : Type of operation: DeviceID | Default: 852; Ambient temperature [°C] : -40...90; Storage temperature [°C] : -40...100; Materials : 1.4542 (17-4 PH / 630); stainless steel (1.4404 / 316L); PEI; Materials (wetted parts) : stainless steel (1.4305 / 303); 1.4542 (17-4 PH / 630); Min. pressure cycles : 60 million; (at 1.2 times nominal pressure); Tightening torque [Nm] : 50; (recommended tightening torque; depends on lubrication, seal and pressure rating); Process connection : threaded connection 1/4" NPT external thread internal thread:M5; Restrictor element integrated : yes

Electronic pressure monitor; Operating voltage [V] : 18...30 DC; Min. insulation resistance [MΩ] : 100; (500 V DC); Protection class : III; Reverse polarity protection : yes; Power-on delay time [s] : < 0.3; Total number of outputs : 2; Output signal : switching signal; IO-Link; (configurable); Electrical design : PNP/NPN; Number of digital outputs : 2; Output function : normally open / normally closed; (parameterisable); Max. voltage drop switching output DC [V] : 2; Permanent current rating of switching output DC [mA] : 100; Switching frequency DC [Hz] : < 170; Short-circuit protection : yes; Type of short-circuit protection : pulsed; Overload protection : yes; Measuring range : 0...400 bar: 0...5800 psi: 0...40 MPa; Set point SP : 4...400 bar: 58...5802 psi: 0.4...40 MPa; Reset point rP : 2...398 bar: 30...5773 psi: 0.2...39.8 MPa; In steps of : 0.2 bar: 1 psi: 0.02 MPa; Factory setting : SP1 = 100 bar: rP1 = 92 bar: ou1 = Hno; | SP2 = 300 bar: rP2 = 292 bar: ou2 = Hno; | dS1/dS2 = 0 ms: dr1/dr2 = 0 ms | coF = 0 %: P-n = PnP: dAP= 60 ms; Switch point accuracy [% of the span] : < ± 0,5 (nach DIN EN 61298-2); Repeatability [% of the span] : < ± 0,05; (with temperature fluctuations < 10 K); Characteristics deviation [% of the span] : < ± 0,5; (linearity incl. hysteresis and repeatability, limit value setting to DIN EN IEC 62828-1); Linearity deviation [% of the span] : < ± 0,1 (BFSL) / < ± 0,2 (LS); Hysteresis deviation [% of the span] : < ± 0,2; Long-term stability [% of the span] : < ± 0,1; (per 6 months); Temperature coefficient zero point [% of the span / 10 K] : < 0,1 (-25...90 °C) / < 0,2 (-40...-25 °C); Temperature coefficient span [% of the span / 10 K] : < 0,1 (-25...90 °C) / < 0,2 (-40...-25 °C); Response time [ms] : < 3; Parameter setting options : hysteresis / window; normally open / normally closed; switching logic; switch-on/switch-off delay; Damping; Communication interface : IO-Link; Transmission type : COM2 (38,4 kBaud); IO-Link revision : 1.1; SDCI standard : IEC 61131-9; Profiles : Smart Sensor: Process Data Variable; Device Identification, Device Diagnosis; SIO mode : yes; Required master port type : A; Process data analogue : 2; Process data binary : 2; Min. process cycle time [ms] : 5; Supported DeviceIDs : Type of operation: DeviceID | Default: 851; Ambient temperature [°C] : -40...90; Storage temperature [°C] : -40...100; Materials : 1.4542 (17-4 PH / 630); stainless steel (1.4404 / 316L); PEI; Materials (wetted parts) : stainless steel (1.4305 / 303); 1.4542 (17-4 PH / 630); Min. pressure cycles : 60 million; (at 1.2 times nominal pressure); Tightening torque [Nm] : 50; (recommended tightening torque; depends on lubrication, seal and pressure rating); Process connection : threaded connection 1/4" NPT external thread internal thread:M5; Restrictor element integrated : yes

Pressure switch with IO-Link; Operating voltage [V] : 18...30 DC; Min. insulation resistance [MΩ] : 100; (500 V DC); Protection class : III; Reverse polarity protection : yes; Power-on delay time [s] : < 0.3; Total number of outputs : 2; Output signal : switching signal; IO-Link; (configurable); Electrical design : PNP/NPN; Number of digital outputs : 2; Output function : normally open / normally closed; (parameterisable); Max. voltage drop switching output DC [V] : 2; Permanent current rating of switching output DC [mA] : 100; Switching frequency DC [Hz] : < 170; Short-circuit protection : yes; Type of short-circuit protection : pulsed; Overload protection : yes; Measuring range [MPa] : 0...10; Set point SP [MPa] : 0.1...10; Reset point rP [MPa] : 0.05...9.95; In steps of [MPa] : 0.005; Factory setting : SP1 = 2.5 MPa: rP1 = 2.3 MPa: ou1 = Hno; | SP2 = 7.5 MPa: rP2 = 7.3 MPa: ou2 = Hno; | dS1/dS2 = 0 ms: dr1/dr2 = 0 ms | coF = 0 %: P-n = PnP: dAP= 60 ms; Switch point accuracy [% of the span] : < ± 0,5 (nach DIN EN 61298-2); Repeatability [% of the span] : < ± 0,05; (with temperature fluctuations < 10 K); Characteristics deviation [% of the span] : < ± 0,5; (linearity incl. hysteresis and repeatability, limit value setting to DIN EN IEC 62828-1); Linearity deviation [% of the span] : < ± 0,1 (BFSL) / < ± 0,2 (LS); Hysteresis deviation [% of the span] : < ± 0,2; Long-term stability [% of the span] : < ± 0,1; (per 6 months); Temperature coefficient zero point [% of the span / 10 K] : < 0,1 (-25...90 °C) / < 0,2 (-40...-25 °C); Temperature coefficient span [% of the span / 10 K] : < 0,1 (-25...90 °C) / < 0,2 (-40...-25 °C); Response time [ms] : < 3; Parameter setting options : hysteresis / window; normally open / normally closed; switching logic; switch-on/switch-off delay; Damping; Communication interface : IO-Link; Transmission type : COM2 (38,4 kBaud); IO-Link revision : 1.1; SDCI standard : IEC 61131-9; Profiles : Smart Sensor: Process Data Variable; Device Identification, Device Diagnosis; SIO mode : yes; Required master port type : A; Process data analogue : 2; Process data binary : 2; Min. process cycle time [ms] : 5; Supported DeviceIDs : Type of operation: DeviceID | Default: 782; Ambient temperature [°C] : -40...90; Storage temperature [°C] : -40...100; Materials : 1.4542 (17-4 PH / 630); stainless steel (1.4404 / 316L); PEI; Materials (wetted parts) : stainless steel (1.4305 / 303); 1.4542 (17-4 PH / 630); Min. pressure cycles : 60 million; (at 1.2 times nominal pressure); Tightening torque [Nm] : 50; (recommended tightening torque; depends on lubrication, seal and pressure rating); Process connection : threaded connection R 1/4 external thread internal thread:M5; Restrictor element integrated : yes

Pressure switch with IO-Link; Operating voltage [V] : 18...30 DC; Min. insulation resistance [MΩ] : 100; (500 V DC); Protection class : III; Reverse polarity protection : yes; Power-on delay time [s] : < 0.3; Total number of outputs : 2; Output signal : switching signal; IO-Link; (configurable); Electrical design : PNP/NPN; Number of digital outputs : 2; Output function : normally open / normally closed; (parameterisable); Max. voltage drop switching output DC [V] : 2; Permanent current rating of switching output DC [mA] : 100; Switching frequency DC [Hz] : < 170; Short-circuit protection : yes; Type of short-circuit protection : pulsed; Overload protection : yes; Measuring range [MPa] : -0.1...2.5; Set point SP [MPa] : -0.075...2.5; Reset point rP [MPa] : -0.087...2.488; In steps of [MPa] : 0.001; Factory setting : SP1 = 0.625 MPa: rP1 = 0.575 MPa: ou1 = Hno; | SP2 = 1.875 MPa: rP2 = 1.825 MPa: ou2 = Hno; | dS1/dS2 = 0 ms: dr1/dr2 = 0 ms | coF = 0 %: P-n = PnP: dAP= 60 ms; Switch point accuracy [% of the span] : < ± 0,5 (nach DIN EN 61298-2); Repeatability [% of the span] : < ± 0,05; (with temperature fluctuations < 10 K); Characteristics deviation [% of the span] : < ± 0,5; (linearity incl. hysteresis and repeatability, limit value setting to DIN EN IEC 62828-1); Linearity deviation [% of the span] : < ± 0,1 (BFSL) / < ± 0,2 (LS); Hysteresis deviation [% of the span] : < ± 0,2; Long-term stability [% of the span] : < ± 0,1; (per 6 months); Temperature coefficient zero point [% of the span / 10 K] : < 0,1 (-25...90 °C) / < 0,2 (-40...-25 °C); Temperature coefficient span [% of the span / 10 K] : < 0,1 (-25...90 °C) / < 0,2 (-40...-25 °C); Response time [ms] : < 3; Parameter setting options : hysteresis / window; normally open / normally closed; switching logic; switch-on/switch-off delay; Damping; Communication interface : IO-Link; Transmission type : COM2 (38,4 kBaud); IO-Link revision : 1.1; SDCI standard : IEC 61131-9; Profiles : Smart Sensor: Process Data Variable; Device Identification, Device Diagnosis; SIO mode : yes; Required master port type : A; Process data analogue : 2; Process data binary : 2; Min. process cycle time [ms] : 5; Supported DeviceIDs : Type of operation: DeviceID | Default: 783; Ambient temperature [°C] : -40...90; Storage temperature [°C] : -40...100; Materials : 1.4542 (17-4 PH / 630); stainless steel (1.4404 / 316L); PEI; Materials (wetted parts) : stainless steel (1.4305 / 303); 1.4542 (17-4 PH / 630); Min. pressure cycles : 60 million; (at 1.2 times nominal pressure); Tightening torque [Nm] : 50; (recommended tightening torque; depends on lubrication, seal and pressure rating); Process connection : threaded connection R 1/4 external thread internal thread:M5; Restrictor element integrated : yes

Pressure switch with IO-Link; Operating voltage [V] : 18...30 DC; Min. insulation resistance [MΩ] : 100; (500 V DC); Protection class : III; Reverse polarity protection : yes; Power-on delay time [s] : < 0.3; Total number of outputs : 2; Output signal : switching signal; IO-Link; (configurable); Electrical design : PNP/NPN; Number of digital outputs : 2; Output function : normally open / normally closed; (parameterisable); Max. voltage drop switching output DC [V] : 2; Permanent current rating of switching output DC [mA] : 100; Switching frequency DC [Hz] : < 170; Short-circuit protection : yes; Type of short-circuit protection : pulsed; Overload protection : yes; Measuring range : -100...1000 kPa: -0.1...1 MPa; Set point SP [MPa] : -0.09...1; Reset point rP [MPa] : -0.095...0.995; In steps of [MPa] : 0.0005; Factory setting : SP1 = 0.25 MPa: rP1 = 0.23 MPa: ou1 = Hno; | SP2 = 0.75 MPa: rP2 = 0.73 MPa: ou2 = Hno; | dS1/dS2 = 0 ms: dr1/dr2 = 0 ms | coF = 0 %: P-n = PnP: dAP= 60 ms; Switch point accuracy [% of the span] : < ± 0,5 (nach DIN EN 61298-2); Repeatability [% of the span] : < ± 0,05; (with temperature fluctuations < 10 K); Characteristics deviation [% of the span] : < ± 0,5; (linearity incl. hysteresis and repeatability, limit value setting to DIN EN IEC 62828-1); Linearity deviation [% of the span] : < ± 0,1 (BFSL) / < ± 0,2 (LS); Hysteresis deviation [% of the span] : < ± 0,2; Long-term stability [% of the span] : < ± 0,1; (per 6 months); Temperature coefficient zero point [% of the span / 10 K] : < 0,1 (-25...90 °C) / < 0,2 (-40...-25 °C); Temperature coefficient span [% of the span / 10 K] : < 0,1 (-25...90 °C) / < 0,2 (-40...-25 °C); Response time [ms] : < 3; Parameter setting options : hysteresis / window; normally open / normally closed; switching logic; switch-on/switch-off delay; Damping; Communication interface : IO-Link; Transmission type : COM2 (38,4 kBaud); IO-Link revision : 1.1; SDCI standard : IEC 61131-9; Profiles : Smart Sensor: Process Data Variable; Device Identification, Device Diagnosis; SIO mode : yes; Required master port type : A; Process data analogue : 2; Process data binary : 2; Min. process cycle time [ms] : 5; Supported DeviceIDs : Type of operation: DeviceID | Default: 784; Ambient temperature [°C] : -40...90; Storage temperature [°C] : -40...100; Materials : 1.4542 (17-4 PH / 630); stainless steel (1.4404 / 316L); PEI; Materials (wetted parts) : stainless steel (1.4305 / 303); 1.4542 (17-4 PH / 630); Min. pressure cycles : 60 million; (at 1.2 times nominal pressure); Tightening torque [Nm] : 50; (recommended tightening torque; depends on lubrication, seal and pressure rating); Process connection : threaded connection R 1/4 external thread internal thread:M5; Restrictor element integrated : yes

Pressure switch with IO-Link; Operating voltage [V] : 18...30 DC; Min. insulation resistance [MΩ] : 100; (500 V DC); Protection class : III; Reverse polarity protection : yes; Power-on delay time [s] : < 0.3; Total number of outputs : 2; Output signal : switching signal; IO-Link; (configurable); Electrical design : PNP/NPN; Number of digital outputs : 2; Output function : normally open / normally closed; (parameterisable); Max. voltage drop switching output DC [V] : 2; Permanent current rating of switching output DC [mA] : 100; Switching frequency DC [Hz] : < 170; Short-circuit protection : yes; Type of short-circuit protection : pulsed; Overload protection : yes; Measuring range [MPa] : 0...40; Set point SP [MPa] : 0.4...40; Reset point rP [MPa] : 0.2...39.8; In steps of [MPa] : 0.02; Factory setting : SP1 = 10 MPa: rP1 = 9.2 MPa: ou1 = Hno; | SP2 = 30 MPa: rP2 = 29.2 MPa: ou2 = Hno; | dS1/dS2 = 0 ms: dr1/dr2 = 0 ms | coF = 0 %: P-n = PnP: dAP= 60 ms; Switch point accuracy [% of the span] : < ± 0,5 (nach DIN EN 61298-2); Repeatability [% of the span] : < ± 0,05; (with temperature fluctuations < 10 K); Characteristics deviation [% of the span] : < ± 0,5; (linearity incl. hysteresis and repeatability, limit value setting to DIN EN IEC 62828-1); Linearity deviation [% of the span] : < ± 0,1 (BFSL) / < ± 0,2 (LS); Hysteresis deviation [% of the span] : < ± 0,2; Long-term stability [% of the span] : < ± 0,1; (per 6 months); Temperature coefficient zero point [% of the span / 10 K] : < 0,1 (-25...90 °C) / < 0,2 (-40...-25 °C); Temperature coefficient span [% of the span / 10 K] : < 0,1 (-25...90 °C) / < 0,2 (-40...-25 °C); Response time [ms] : < 3; Parameter setting options : hysteresis / window; normally open / normally closed; switching logic; switch-on/switch-off delay; Damping; Communication interface : IO-Link; Transmission type : COM2 (38,4 kBaud); IO-Link revision : 1.1; SDCI standard : IEC 61131-9; Profiles : Smart Sensor: Process Data Variable; Device Identification, Device Diagnosis; SIO mode : yes; Required master port type : A; Process data analogue : 2; Process data binary : 2; Min. process cycle time [ms] : 5; Supported DeviceIDs : Type of operation: DeviceID | Default: 780; Ambient temperature [°C] : -40...90; Storage temperature [°C] : -40...100; Materials : 1.4542 (17-4 PH / 630); stainless steel (1.4404 / 316L); PEI; Materials (wetted parts) : stainless steel (1.4305 / 303); 1.4542 (17-4 PH / 630); Min. pressure cycles : 60 million; (at 1.2 times nominal pressure); Tightening torque [Nm] : 50; (recommended tightening torque; depends on lubrication, seal and pressure rating); Process connection : threaded connection R 1/4 external thread internal thread:M5; Restrictor element integrated : yes